--- title: "Washer not spinning" description: "Clothes heavy with water at the end of a program that otherwise ran normally. Three free things account for most of these and all three can be settled before anybody" url: "https://askomiami.support/symptoms/washer-not-spinning/" date_modified: "2026-09-13" Appliance type: "Washers" --- # Asko washer not spinning ### What to do in the next ten minutes Take the load out and run a spin-only program on the empty drum. If it spins, the problem is drainage or balance and this becomes a much cheaper visit. If it does not, listen: a click and then nothing is usually the door lock; a hum without rotation is the motor or something jammed. Turn the drum by hand with the machine unplugged and note whether it moves freely. ### Why the machine gives up rather than complaining An unbalanced load at full spin will walk a machine across a tiled floor, so the control measures balance before it accelerates and abandons the attempt if it cannot get there. On the display panels that is reported as an imbalance message the manual explicitly says needs no action; on the analog machines it is not reported at all and you simply find wet washing. Both are the machine working correctly, which is why the empty-drum test matters so much. ### The repair that prevents the expensive one Worn shock absorbers are the quietest failure on a washing machine: nothing reports them, and the first sign is a machine that spins less reliably and moves more. Left alone, the extra travel loads the drum bearing, and that is a day’s strip-down instead of an afternoon’s parts. On a steel-framed machine worth keeping, this is the cheapest protection there is. It has not drained The interlock again. Everything upstream of the spin looks fine and the machine simply will not accelerate a full drum. The door lock has worn The machine proves the door is locked before it spins, and a lock that no longer confirms it stops the cycle at exactly this point. Small part, common failure. The suspension has gone soft Worn shock absorbers let the drum travel further on every attempt, the balance check gives up, and the machine drops out of spin rather than reporting anything. Does it spin empty? The single most useful test on this complaint, and it costs one program. Write down what happens. Is one heavy item in the load? A bath mat or a single towel is the classic. The machine will try ten times to redistribute it and then continue without spinning, which is correct behavior. Does the drum move a lot when you push it? With the power off, push the drum and let go. One that bounces rather than settling has lost its damping. The load comes out soaked after a cycle that seemed to finish What it usually means Run a spin-only program on an empty drum — it separates three causes in five minutes A machine holding water will never spin, by design Persistent imbalance on ordinary loads is worn suspension, not laundry What to do in the next ten minutes Take the load out and run a spin-only program on the empty drum. If it spins, the problem is drainage or balance and this becomes a much cheaper visit. If it does not, listen: a click and then nothing is usually the door lock; a hum without rotation is the motor or something jammed. Turn the drum by hand with the machine unplugged and note whether it moves freely. Why the machine gives up rather than complaining An unbalanced load at full spin will walk a machine across a tiled floor, so the control measures balance before it accelerates and abandons the attempt if it cannot get there. On the display panels that is reported as an imbalance message the manual explicitly says needs no action; on the analog machines it is not reported at all and you simply find wet washing. Both are the machine working correctly, which is why the empty-drum test matters so much. The repair that prevents the expensive one Worn shock absorbers are the quietest failure on a washing machine: nothing reports them, and the first sign is a machine that spins less reliably and moves more. Left alone, the extra travel loads the drum bearing, and that is a day’s strip-down instead of an afternoon’s parts. On a steel-framed machine worth keeping, this is the cheapest protection there is. ### Can I put it on a second spin? Yes, and it is a fair workaround for one load. If it becomes the routine, the machine is telling you something and it will not improve. ### It spins but very slowly. Different problem from not spinning at all — usually the motor control or the drive rather than balance. Worth saying which it is. --- **[Read full article: Washer not spinning](https://askomiami.support/symptoms/washer-not-spinning/)**